Fluke 9105 Manuel d'utilisateur Page 5
- Page / 65
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8.11.5.3SCO ................................................42
9 Digital Communication Interface ....................43
9.1 Serial Communications ..................................43
9.1.1 Wiring ..................................................43
9.1.2 Setup ...................................................43
9.1.2.1 BAUD Rate ............................................44
9.1.2.2 Sample Period...........................................44
9.1.2.3 Duplex Mode ...........................................44
9.1.2.4 Linefeed..............................................44
9.1.3 Serial Operation .............................................45
9.2 IEEE-488 Communication .................................45
9.2.1 Setup ...................................................45
9.2.1.1 IEEE-488 Interface Address ....................................45
9.2.2 IEEE-488 Operation ............................................45
9.3 Interface Commands ...................................46
10 Test Probe Calibration .........................51
10.1 Comparison Methods ...................................51
10.1.1 Direct Calibration .............................................51
10.1.2 Comparison Calibration ..........................................51
10.1.3 Calibration of Multiple Probes .......................................52
10.2 Dry-Well Characteristics..................................52
10.2.1 Vertical Gradient .............................................53
10.2.2 Stabilization and Accuracy ........................................53
11 Calibration Procedure .........................55
11.1 Calibration Procedure...................................55
11.1.1 Calibration Equipment ..........................................55
11.1.2 Calibration ................................................55
12 Maintenance .............................57
13 Troubleshooting ............................59
13.1 Troubleshooting .....................................59
13.2 Comments ........................................60
13.2.1 EMC Directive ...............................................60
13.2.2 Low Voltage Directive (Safety) ......................................60
13.3 Wiring Diagrams .....................................61
iii
- 9105 / 9107 1
- Dry-well Calibrator 1
- Rev.2A2801 2
- Table of Contents 3
- 1.2 Safety Information 9
- 9105/9107 3 10
- 1 Before You Start 10
- Figure 1 Top View 10
- Cautions 11
- 9105/9107 5 12
- 6 Hart Scientific 13
- 2 Introduction 14
- 3.1 Specifications 15
- 3.2 Environmental Conditions 15
- 3.3 Warranty 16
- 4 Safety Guidelines 17
- 12 Hart Scientific 18
- 5 Quick Start 19
- 5.4 Setting the Temperature 20
- 6 Parts and Controls 21
- 6.2 Front Panel 22
- 3/16" Well 23
- 1/4" Well 23
- 1/8" Well 23
- 6.4 Well Insulator (9107only) 24
- 9105/9107 19 25
- 7 General Operation 26
- 7.3 Setting the Temperature 27
- 7.4 Calibrating Probes 27
- 8 Controller Operation 28
- Temperature 29
- 8.3 Temperature Set-point 30
- 8.4 Scan 31
- 8.5 Temperature Display Hold 32
- 8.5.2 Mode Setting 33
- 9105/9107 29 34
- 30 Hart Scientific 35
- 9105/9107 31 36
- Figure 7 Switch Test Data 36
- 32 Hart Scientific 37
- 8.7 Secondary Menu 39
- 8.8 Heating Power 39
- 8.9 Proportional Band 39
- -12 Pct 40
- 8.10 Cut-out 41
- 8.11 Controller Configuration 42
- 8.11.2 Operating Parameters 43
- 8.11.2.3 Soak Stability 44
- 8.11.3.1 BAUD Rate 44
- 8.11.3.2 Sample Period 45
- 8.11.3.3 Duplex Mode 45
- 8.11.3.4 Linefeed 45
- 8.11.4.1 IEEE-488 Address 46
- 8.11.4.2 Termination 46
- 8.11.5 Calibration Parameters 47
- 9.1 Serial Communications 48
- 9.1.2.1 BAUD Rate 49
- 9.1.2.2 Sample Period 49
- 9.1.2.3 Duplex Mode 49
- 9.1.2.4 Linefeed 49
- 9.2 IEEE-488 Communication 50
- 9.3 Interface Commands 51
- 10 Test Probe Calibration 55
- 10.2 Dry-Well Characteristics 56
- 10.2.1 Vertical Gradient 57
- 11 Calibration Procedure 58
- 56 Hart Scientific 59
- 12 Maintenance 60
- 58 Hart Scientific 61
- 13 Troubleshooting 62
- 13.2 Comments 63
- 13.3 Wiring Diagrams 64
- 62 Hart Scientific 65
- Figure 11 9107 Wiring Diagram 65
Produits connexes et manuels pour Mesure, test et contrôle Fluke 9105
(140 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.098 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels