Fluke 5020A Manuel d'utilisateur Page 120
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5020A
Users Manual
6-50
measure bit.
Bit 3 Channel 2 humidity measure
bit.
Bit 4 Not used
Bit 5 Not used
Bit 6 Not used.
Bit 7 Not used.
Example: STAT:MEAS:COND?
Response: 15
STATus:MEASure:ENABle?
This command returns the Measurement Status Enable Register (see
STATus:MEASure:ENABle <num> command below).
Example: STAT:MEAS:ENAB?
Response: 15
STATus:MEASure:ENABle <num>|MIN|MAX|DEF
This command sets the Measure Status Enable Register. This register determines which
event bits of the Measure Status Event Register affect the Measure Status Bit of the
Status Byte Register. If any bit in the Measure Status Event Register is set (1) while its
corresponding mask bit in the Measure Status Enable Register is set, the Measure Status
Bit in the Status Byte Register will be set. The value of the <num> parameter is a number
from 0 to 15 that is the sum of the binary-weighted values of each mask bit. The Measure
Status Event Register is described in Section 8.4.11.13, STATus:MEASure?. The
following example causes the Measure Status Bit in the Status Byte Register to be set
when measurements on both channels have been completed.
Example: STAT:MEAS:ENAB 15
Response: 15
STATus:OPERation?
This command reads and clears the Operation Status Event Register. The value returned
indicates the condition of each of the eight bits of the register by adding the binary-
weighted values of each bit. The meaning of each bit, when set (1), is as follows where 0
is the least significant and 7 is the most significant:
0: no measurement
Bit 0 Not used.
Bit 1 Not used.
Bit 2 Not used.
Bit 3 Not used.
Bit 4 Measurement Complete bit.
Bit 5 Not used.
Bit 6 Not used.
Bit 7 Not used.
Example: STAT:OPER?
Response: 16
STATus:OPERation:CONDition?
This command reads the Operation Status Condition Register. Reading this register does
not affect it. The value returned indicates the condition of each of the eight bits of the
- Users Manual 1
- Table of Contents 3
- ii 4
- Contents (continued) 5
- iii 5
- iv 6
- List of Tables 7
- vi 8
- List of Figures 9
- viii 10
- Chapter 1 11
- Symbols Used 14
- Safety Information 14
- Safety Information 1 15
- Technical Support 16
- Specifications 17
- Environmental Conditions 18
- Quick Start 19
- Introduction 2 21
- Connect the Power Source 22
- Switch the Power On 22
- Measure Temperature 22
- Parts and Controls 23
- Front Panel 25
- Top Panel 26
- Right Side Panel 26
- Left Side Panel 27
- Back Panel 27
- Quick Buttons 28
- Configurations 28
- Accessories 28
- Accessories 3 29
- General Operation 31
- DC Power Source 33
- Battery 33
- Unit of Temperature 35
- Recording Measurements 35
- Sensors 35
- Menu Functions 37
- Channel Menu 39
- Figure 5-3. Channel Menu 40
- Channel Menu 5 41
- Figure 5-6. Sensor Lock 42
- Display Menu 43
- Figure 5-9. Display Menu 44
- Figure 5-10. Display Setting 44
- Display Menu 5 45
- 5-11 47
- Figure 5-14. Graph Scale 48
- Data Menu 49
- Figure 5-17. Data Record 50
- Data Menu 5 51
- 5-15 51
- 5-17 53
- Figure 5-22. Data Storage 54
- Figure 5-23. Data Clear 54
- 5-19 55
- Figure 5-25. Stats Setting 56
- Figure 5-26. Stats View 56
- 5-21 57
- Figure 5-29. Stats Clear 58
- Figure 5-30. Data Card 58
- 5-23 59
- Alarm Menu 60
- Alarm Menu 5 61
- 5-25 61
- Figure 5-35. Sensor Alarm 62
- System Menu 63
- Figure 5-38. System Menu 64
- Figure 5-39. System Setting 64
- System Menu 5 65
- 5-29 65
- 5-31 67
- Figure 5-43. IR 68
- 5-33 69
- Figure 5-45. System Info 70
- Chapter 6 71
- Communications 73
- Interface Commands 74
- Interface Commands 6 75
- 6-11 81
- Commands 82
- 6-13 83
- 6-15 85
- 6-17 87
- 6-19 89
- 6-21 91
- 6-23 93
- 6-25 95
- 6-27 97
- 6-29 99
- Commands 6 101
- 6-31 101
- 6-33 103
- 6-35 105
- 6-37 107
- 6-39 109
- 6-41 111
- 6-43 113
- 6-45 115
- 6-47 117
- 6-49 119
- 6-51 121
- 6-53 123
- Calibration Procedure 125
- Introduction 127
- Equipment 127
- Preparation 127
- Calibration Points 127
- TSLTSLLTS ∆+= 129
- Chapter 8 131
- Maintenance 133
- Troubleshooting 133
- Downloading Recorded Data 135
- CE Comments 136
- Frequently Asked Questions 136
- Index (continued) 141
Produits connexes et manuels pour Mesure, test et contrôle Fluke 5020A
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels