Fluke 5020A Manuel d'utilisateur Page 98
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5020A
Users Manual
6-28
DATa:DSTatistics:RECord:ETIMe? [<num>]
Returns the daily statistics recording end time.
Example: DAT:DST:REC:ETIM?
Response: 23,59,59
The <num> parameter specifies the daily statistics record number. If none is specified,
record 1 is assumed. The response is returned in the format, <hour>,<minute>,<second>.
DATa:DSTatistics:RECord:FIND? (<year>,<month>,<day>)
Returns the daily statistics record number for the given date.
Example: DAT:DST:REC:FIND? 2003,9,13
Response: 25
If no daily statistics were recorded for the given date a 0 is returned.
DATa:DSTatistics:RECord:VALue? <num>,<chn>,<type>
Returns the daily statistics statistical calculation.
Example: DAT:DST:REC:VAL? 1,1,1
Response: 25.559,0.733,23.097,27.203,4.106,43200,17.16,0
The <num> parameter specifies the daily statistics record number. The <chn> parameter
specifies the channel (1 or 2). The <type> parameter specifies the statistic: average (1),
standard deviation (2), minimum (3), maximum (4), spread (5), maximum rate (7), or
alarm count (8). Temperature values are in the current temperature unit, C of F.
DATa:RECord:CLEar
Clears all recorded measurement data.
Example: DAT:REC:CLE
This command is password protected. To access this command when the
SYST:PASS:REC is enabled, the password must be successfully entered using the
SYST:PASS:CEN <pass> command (see Password Commands).
DATa:RECord:FEED:RHUMidity<chn>?
Returns the state of the humidity recording enable for the specified channel.
Example: DAT:REC:FEED:RHUM1?
Response: 1
The RHUMidity suffix <chn>, specifies the channel (1 or 2). A value of 1 is returned if
the humidity recording for the specified channel is enabled. A value of 0 is returned if the
humidity recording for the specified channel is disabled.
DATa:RECord:FEED:RHUMidity<chn> <bool>
Sets the state of the humidity recording enable for the specified channel.
Example: DAT:REC:FEED:RHUM1 0
The RHUMidity suffix <chn>, specifies the channel (1 or 2). The <bool> parameter turns
the humidity recording for the specified channel on (1 or ON) or off (0 or OFF). This
command may be password protected (see Password Commands).
- Users Manual 1
- Table of Contents 3
- ii 4
- Contents (continued) 5
- iii 5
- iv 6
- List of Tables 7
- vi 8
- List of Figures 9
- viii 10
- Chapter 1 11
- Symbols Used 14
- Safety Information 14
- Safety Information 1 15
- Technical Support 16
- Specifications 17
- Environmental Conditions 18
- Quick Start 19
- Introduction 2 21
- Connect the Power Source 22
- Switch the Power On 22
- Measure Temperature 22
- Parts and Controls 23
- Front Panel 25
- Top Panel 26
- Right Side Panel 26
- Left Side Panel 27
- Back Panel 27
- Quick Buttons 28
- Configurations 28
- Accessories 28
- Accessories 3 29
- General Operation 31
- DC Power Source 33
- Battery 33
- Unit of Temperature 35
- Recording Measurements 35
- Sensors 35
- Menu Functions 37
- Channel Menu 39
- Figure 5-3. Channel Menu 40
- Channel Menu 5 41
- Figure 5-6. Sensor Lock 42
- Display Menu 43
- Figure 5-9. Display Menu 44
- Figure 5-10. Display Setting 44
- Display Menu 5 45
- 5-11 47
- Figure 5-14. Graph Scale 48
- Data Menu 49
- Figure 5-17. Data Record 50
- Data Menu 5 51
- 5-15 51
- 5-17 53
- Figure 5-22. Data Storage 54
- Figure 5-23. Data Clear 54
- 5-19 55
- Figure 5-25. Stats Setting 56
- Figure 5-26. Stats View 56
- 5-21 57
- Figure 5-29. Stats Clear 58
- Figure 5-30. Data Card 58
- 5-23 59
- Alarm Menu 60
- Alarm Menu 5 61
- 5-25 61
- Figure 5-35. Sensor Alarm 62
- System Menu 63
- Figure 5-38. System Menu 64
- Figure 5-39. System Setting 64
- System Menu 5 65
- 5-29 65
- 5-31 67
- Figure 5-43. IR 68
- 5-33 69
- Figure 5-45. System Info 70
- Chapter 6 71
- Communications 73
- Interface Commands 74
- Interface Commands 6 75
- 6-11 81
- Commands 82
- 6-13 83
- 6-15 85
- 6-17 87
- 6-19 89
- 6-21 91
- 6-23 93
- 6-25 95
- 6-27 97
- 6-29 99
- Commands 6 101
- 6-31 101
- 6-33 103
- 6-35 105
- 6-37 107
- 6-39 109
- 6-41 111
- 6-43 113
- 6-45 115
- 6-47 117
- 6-49 119
- 6-51 121
- 6-53 123
- Calibration Procedure 125
- Introduction 127
- Equipment 127
- Preparation 127
- Calibration Points 127
- TSLTSLLTS ∆+= 129
- Chapter 8 131
- Maintenance 133
- Troubleshooting 133
- Downloading Recorded Data 135
- CE Comments 136
- Frequently Asked Questions 136
- Index (continued) 141
Produits connexes et manuels pour Mesure, test et contrôle Fluke 5020A
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels